Metal Tile Roofing in Florida

The full profile of a traditional tile roof, built on interlocking coated-metal panels that are far lighter than concrete or clay, and engineered for Florida wind and rain.

Why Metal Tile Roofing Is a Smart Choice in Florida

For homeowners who want a metal roof that looks like tile, metal tile panels deliver the full Spanish and Mediterranean barrel profile without tile’s two big weaknesses in Florida: weight and breakage. Panels interlock and fasten mechanically, so they stay put in high wind instead of sliding or lifting the way individual tiles can. And after a storm, there are no cracked tiles to hunt down and match; the panel either sheds the impact or gets swapped as a section.

Because metal tile is stamped from coated steel rather than cast from concrete or clay, it weighs a small fraction as much. That takes real load off your framing, which matters on older homes and on re-roofs where the structure was never designed for heavy tile. High-quality finishes resist fading, surface corrosion, and UV damage through years of Florida sun.

Thinking About Clay Tile in Melbourne or Brevard County? Read This First

A lot of the tile conversations we have start in Melbourne, Suntree, and Viera, where clay and concrete tile neighborhoods are everywhere and so are cracked-tile repair bills. Here’s the honest comparison. Clay tile looks beautiful and lasts, but it’s brittle under foot traffic and windborne debris, expensive to repair because matching discontinued tile is a scavenger hunt, and heavy enough that repeated repairs stress the underlayment beneath. Metal tile keeps the same street-view profile, cuts the weight dramatically, carries hurricane-rated wind performance, and turns “find a matching tile from 1995” into “replace a panel section.” If your tile roof is on its second or third repair cycle, get a metal tile quote before you sink more money into clay.

Metal Tile Roofing Services We Provide

  • Installation & Replacement: new metal tile roofs on residential properties, with full roof-deck inspection and repair before installation.

  • Repairs: addressing loosened interlocking panels, sealant failure, and isolated panel damage.

  • Upgrades from Concrete or Clay Tile: comparing weight, cost, and lifespan, then designing a metal tile system that keeps the tile look with far less structural load.

We install metal tile across our service area, with strong demand in Melbourne and the tile-look neighborhoods of Vero Beach and the Treasure Coast. Related options worth comparing: stone-coated steel and metal shingles. Ready for numbers? Request a free quote.

Trusted Metal Roofing Manufacturers & Distributors

We build with materials from top national manufacturers and well-known Florida distributors.

SRS Building Products - Metal Roofing Distributor in FloridaQXO Building and Metal Roofing Products - Metal Roofing Distributor in Florida
Dynamic Metals - Metal Roofing Manufacturer Distributor in Florida
Decra Metal Roofing Manufacturer - Stone Coated Metal Roofs in Florida
Tilcor Metal Shingles, Metal Tile Manufacturer in Florida
ABC Supply - Roofing Distributor in Florida
SunShine Metal Supply - Metal Roofing Manufacturer and Supply in Florida
Roser Metal Roofing Manufacturer - Stone Coated Metal Roofs in Florida
TEK Stone Coated Metal Roofs and TEK Metal Shingles in Florida
1st Coast Metal Roofing Supply - Metal Roofing Manufacturer Distributor in Florida
Queen Stone Coated Tile, Shingle and Shake Manufacturer in FloridaUnified Steel Stone Coated Metal Roofing in Florida
View all 24 manufacturers & distributors
GAF Metal Roofing Manufacturer - GAF TimberSteel Metal Shingles in Florida
IKO Metal Roofing and Metal Shingle Manufacturer
Atlas Roofing Manufacturer
Certainteed Roofing Manufacturer
Owens Corning Roofing Manufacturer
Westlake Metal Roof Products in Florida
Sheffield Metals International - Metal Roofing Coil and Panel Manufacturer
Tri County Metals - Metal Roofing Manufacturer Distributor in Florida
Gulf Coast Metal Roofing Supply and Manufacturing Florida
Metal Roof Factory - Metal Roofing Manufacturer Distributor in Florida
Gulf Eagle Supply - Metal Roofing Distributor in Florida
Eagle Roofing Tile Distributor

Brand names and logos appear here to show the roofing materials we install and source. All trademarks belong to their respective owners, and listing them does not imply certification, endorsement, or any formal partnership.

Metal Tile Roofing in Florida Questions

Does metal tile roofing really look like a traditional tile roof?

Yes. Metal tile panels replicate the dimensional barrel-tile profile from the street, while the interlocking coated-metal construction underneath delivers wind and water resistance that clay and concrete can't match.

Is a metal roof that looks like tile lighter than concrete or clay tile?

Yes, dramatically. Clay and concrete tile can weigh 600 to 1,000 pounds per square, while metal tile panels weigh a small fraction of that. Less structural load matters when replacing an older roof or building where framing capacity is a concern.

Is metal tile roofing noisy when it rains?

Not with proper installation. Over solid decking with quality underlayment and normal attic insulation, interior sound levels are comparable to other roofing materials.

Can my existing concrete or clay tile roof be replaced with metal tile?

In most cases, yes. We remove the old tile, inspect and repair the deck (often relieved of a ton or more of weight), then install the new interlocking system to current code and manufacturer specs. We confirm fit during your free inspection.

Free Metal Tile Roof Estimate

Call us at (800) 303-3309 or request your free, no-obligation estimate below in 3 easy steps. We'll carefully evaluate your roof and answer your questions.

Current Roof Condition *

Free Metal Roof Estimate & Inspection

Call us at (800) 303-3309 or request your free, no-obligation estimate. We'll carefully evaluate your roof and answer your questions.

Get a Free Roof Quote  Call (800) 303-3309